1946 Willys Jeep CJ-2A VEC - Museum Ready

1946 Willys VEC (Very Early Civilian) CJ-2A Jeep - Museum Ready
Offered is a 1946 CJ-2A that has undergone a frame-off, ut and bolt, otisserie restoration. This is a very early civilian version, dentified by square windshield plates, olumn shift, ool indents, F' script bolts in drive train, rame tag on the outside of the driver front gusset and three data plates on the dash.
I acquired this Willys Jeep CJ-2A from a Kingman, ansas flying service in 2008 where it was being used as an airport tug. Everything was original, ncut, atching numbers and well preserved in several coats of orange paint. The frame tag, ash data plate and the Willys body tag are each numbered 17968 and correctly located. The motor number is CJ-2A 18464. The AMC numbers on the tailgate and front gusset are matching and both read 8620.
All documentation regarding the rebuild including receipts and notes is included with the vehicle in its restoration notebook. The engine has been professionally rebuilt by Vilas Motor Works of Bryan, exas. The transmission and transfer case were shipped to Herm Tilford - aka 'Herm, he Overdrive Guy' in Brush Prairie, ashington where they were also professionally rebuilt.
The body was completely media blasted and rusted panels removed by drilling out rivets with a rivet extraction tool. New body panels from Krage Motorsports were then welded into place and include the front floorboard with hat channels and the right rear quarter panel.
Meticulous care was taken through extensive research to identify correct paint color for each component. The Harvest Tan was mixed using the original color found inside the headlight rings (a small section of the original paint has been preserved inside each ring for posterity). Wheels were painted to match very early advertisements and photos in the rarely seen two-tone configuration - Sunset Red surrounded by Harvest Tan with hand painted black pin stripes. Paint is a catalyzed 3-part Polyurethene Acrylic by Matthews.
The electrical system has been gone through and components rebuilt (starter and generator) and replaced with period correct items where needed including a replacement wiring harness from Walck's.
New period correct components include radiator, DT tires, ater hose kit and tubes, ir hoses, enerator arm, enerator bushing support and tension bracket (early), attery tray, attery hold down hardware with correct wing nuts, ash knobs, olt meter, ront bumper, ender welting, irewall grommets, ogged fan belt, adiator welting, adiator felt, ooden hood bumper blocks, ood tie-down strap, ebuilt vacuum wiper engine, iper vacuum lines, ulbs, ccelerator pedal, xhaust system, il plug gasket, il hoses, rake hoses, indshield glass, indshield welting, indshield tape, issing windshield star washer, ody to frame welting and bolts, ailgate chains and covers, ail light, ear reflector, aster cylinder, as tank and sender, rake sender, rakes, heel cylinders, s' lines, lugs, lug wires, oints and condenser, ootman loops, ood latches and seat covers from Beachwood Canvas mounted on original springs and seat frames (except for back seat bottom cushion - original is included on request along with original gas tank and sender). There is much more, ut basically the entire vehicle has been disassembled, nspected and reassembled with replacement and correct hardware added where needed - receipts will bear this out.
Vehicle odometer showed 24,745 miles before the rebuild. Odometer was reset to zero and approximately 250 miles have been put on the vehicle since that time in addition to weekly startups and running of the engine for fluid circulation.
The vehicle runs perfectly as it should. All gauges and lights work as they should.
The correctly restored 1946 Texas license plate is available for $100 at the close of the sale but does not convey with the vehicle.
Vehicle is sold as is, here is with no warranty and with clear Texas title. Available for inspection by appointment.
Additional photos at

1946 Jeep CJ-2A Restoration