1965 Shelby Cobra Factory Five custom built perfect condition Fuel Injected

This car is located in Longview, TX and is a one owner car with a clear TX title. It is inperfect condition in every way. It runs 0 to 60 in 1.9 seconds and just under 10 second quarter mile. It comes with Cobra wheels and tires and an extra rear set of cobra wheels and drag slicks. It was hand built to perfection and I do have allreceipts of everything done to the car. Below is a quick list of details on the car.

Engine:

410W built by Keith Craft

Forged 4340 crank and rods

2618 Pistons

11:1 Compression

Steel girdle

TFR R-Series Heads

-Intake ports raised 1/2"

-2.10"In/ 1.60"Ex.

-Titanium retainers

-Flow IN:354@.700 & EX:257@.700

-Crane gold rockers

Matched Super Victor intake w/ raised ports

Comp Cams hyd. roller .613/.644

SFI Balancer & Flywheel

All ARP Hardware

Transmission:

TKO 600 w/ .64 OD

Spec Stage 3+ Clutch/pressure plate

New Shortened driveshaft w/ all Spicer parts

Rearend:

8.8" Fox width

Motorsport 3.55:1 gears

Hardened axles

Carbon Clutches

2.5" long Studs

Suspension:

Front FFR tubular lowers - Pin Drive Width

FFR Adjustable Uppers

Pro Shocks Coil-overs

'01 Cobra spindles

Rear Custom 3-link w/ upper link centered over 3rd member

Adjustable tubular lower control arms

Adjustable tubular upper control arm

Adjustable QA1 Coil overs

Competition Engineering Anti-roll bar

Brakes:

Front - 13" Cobra

Rear - 11.7" Cobra

Custom braided stainless flex lines F&R

1/4" polished stainless hard line w/ stainless aeroquip fitings

'01 Cobra Master cylinder

Cooling:

NASCAR 19"x31" DUAL PASS radiator- HUGE

Custom 1 7/8" hard plumbing

'03 Cobra Cooling fan w/ custom mounts on radiator

Earl's polished aluminum thermostat housing

CSR aluminum filler neck

Polished aluminum filler cap

Polished Edelbrock water pump

Polished March underdrive pulleys

Adjustable fan controller w/ over-ride switch

Electrical:

Painless wiring harness and switches

Polished 200A 3G alternator

Pro Tork mini starter

MSD digital 6

MSD blaster coil

MSD billet bistributor

Aeromotive fuel pump controller

Optima Battery

Large 2-O battery cable

All ground studs welded to frame for good contact

All lighting has quick disconnect plugs

Exhaust:

Custom 1 7/8" ceramic coated headers

Ceramic coated sidepipes

O2 bungs welded for wideband O2

Exterior:

Original style finned aluminum side vents

Original style Cobra front and nose badges

Original style 427 side badges

Polished roll bar bezels

Original style Cobra steering wheel insert

Driver and Passenger side mirrors

Original style wind wings and visors

Chromed quick jack bumpers

Front quick jack grommets

Stainless body washers w/ rubber backing

Door and hood rubber D-molding

Polished fuel filler neck w/ built in locking gas cap

Lucas Clear front parking light lenses

Shelby Motors License plate frame

Polished billet windshield frame bezels

Frame Mods:

Rear frame narrowed to accept 13" rim

Dual ceramic coated roll bars

Battery tray over fuel tank for trunk access

Front Coil over brackets shortened

Front UCA mounting slots filled

Removable steel tube to hard mount radiator

Rear coil over backets mounted inside frame

Curved upper trunk support tube like MKIII

Lowered trunk aluminum for additional room

MKIII hood hinge w/ custom plates bonded on hood

MKIII door hinges

Frame extended to support lower dash

Fuel:

Billet fuel pump

Billet -10AN fuel filter

Braided stainless -10AN fuel line

-10AN in-tank pickup

Race Holley fuel regulator (12-704)

DC Carbs 950 cfm billet carb

Polished billet ball-milled oval aluminum air filter

Polished throttle cable bracket

Braided stainless throttle cable

Interior:

Autometer Cobra style gauges w/ reverse speedo

Adjustable driver seat

Raised passenger seat to match driver

A/C aluminum pedals for all pedals

Stainless cup holders

Driver side Simpson harness upgraded to cam lock style

Polished seat belt bezels

Steering:

Ididit polished aluminum steering column

Integral self canceling turn signals

Polished stainless steering U-Joints

Custon polished stainless steering shaft

Ididit polished aluminum lower ball mount

Flaming river manual rack

Flaming river outer tie rods

Wheels/Tires:

PS Engineering Hallibrand wheels

17" x 8" Frotn & 17" x 9.5" Rear

M/T 26 x 11.5 ET Streets