1966 MUSTANG CONVERTIBLE PROJECT

1966 Ford Mustang Convertible Project

The uni-body of this Mustang has been completely rebuilt. The cowl tank and firewall have been replaced along with the floor pans and rear quarter panels. Theuni-body was sand blasted and primed with red-oxide primer. The undercarriage has been painted black as well as the engine compartment.I have updated the front suspensionwith a CPP mini sub-frame kit allowing the use of tubular upper and lower control arms which eliminate the strut rods. I have added front disc brakes (you will need tobuy calipers and hoses). The carwas an original V8 car with a 3spd manual trans. Ihave aroller 5.0L V8 and C4 automatic trans that go with the car, ut both need to be rebuilt. I also have a new Pony Interior kit for the car. It is in the Blue/White color scheme. I have most all of the parts to put the car back together. I also have a long list of New Parts to come along with the uni-body. I have well over $20,000 in the project so far. I am asking $14,000 for the uni-body and all associated parts. This is a muchbetter deal than buying a made DYNACORN uni-body. If interested, can send more photos tointerested/serious buyers. What would even be better would be for you to come by and look at what I have. Here is a list of the new Parts:

Description Quantity Automatic Trans Shifter Cover 1 8" Axle U-Bolt w/nut 4 Leaf Spring Eye Bolt 2 Door Jam Window Seal (pair) 1 Wire Loom Plastic Retainer clips 5 Seat Side Molding hardware (per seat) 4 Inner Seat Hinge Covers (set) 1 Seat Adjustment Kit (set) 2 Gas/ Brake Line clip install set 1 Spare Tire bolt, ing nut, late 1 Shift Plate Retainer 1 Steering Column Floor gasket 1 Steering Column Floor seal 1 Automatic Trans Shifter Assm. 1 Power Steering Pump Bracket 1 Conv Top Hold down J hooks & pins (set) 1 New Lock Kit (2 doors & Ignition) 1 Door Latch regulator 2 Backup Light Gromets 2 Door Hinge Bolts (per side) 1 Sway Bar End Link Kit (per side) 2 Manual Shifter Boot 1 Manual Shifter Chrome Plate 1 NOS - Running Horse Emblem 2 Front Bumper to Quarter Panel Bracket (left) 1 Front Bumper to Quarter Panel Bracket (right) 1 Cowl Seal Brakets (set) 1 Hood Bumper Kit 2 Door Bumper Kit 1 Wiper Switch Knob 1 Ignition Switch Bezel 1 Rear Quarter Window Window Seal (set) 1 Convertible A Pilar seal 2 Quarter Vent Window Repair Kit 2 Heater Box Seal Kit 1 4 BBL 1" Spacer Plate 1 4 BBL Carb Gasket 2 Window Track Felt Material (4 FT) 1 Trunk Lid Gasket 2 Pony Door Handles - Interior 2 Quarter Window Cranks 4 Front Window Crank 1 Door Handle Cups 2 Pony Interior Installation Kit 1 Pressure Plate Bolt Kit 1 Convertible Top Truss Bolt 1 Accelerator Spring 1 Door Weather Strip 4 Glove Box Striker Kit 1 Interior Screw Kit - Coupe 1 Dash Pad Mounting Kit 1 Spare Tire Braket (to be welded to floor) 1 Seat Track Release Springs 2 Window Crank Springs 4 Window Track Rollers 3 Power Brake Check Valve and Gromet 1 Pony Door Handle Screws 4 Glove Box Cable Kit 1 Heater Knob Set 1 Black Wind Lace (10FT) 1 Voltage Regulator 1 Low Pressure AC hose 1 Electronic Distributor 1 Fog Light Kit (Horse & bars, ight housings, ulbs and wiring 1 New Vent Window Frame - Left 1 New Vent Window Frame - Right 1 York to Sanden AC Compressor Conversion Plate 1 Blue/White Pony Seat Cover set 1 Front Seat Foam Set (per seat) 2 Dash Pad Mounting Kit 1 Rear Valance Panel 1 Door Sill Plates 1 Seat Tracks 1 Gauge Cluster - Wood Grain 1 Motor Mounts 2 Trans Mount 1 Carpet Kit - Blue 1 Kick Panels - Blue 2 Trunk Filler Board 1 Alternator 1 Starter 1 Antena 1 Center Link 1 Inner Tie Rods 2 Cobra Rear Brake Calipers (pair) 1 ADCO Rear Sway Bar 1 ADCO Front Sway Bar (installed) 1 KONI Front Shocks 2 KONI Rear Shocks 2 5 Leaf Mid-Eye rear leaf springs (installed) 2 Rear Shakle Kits (installed) 2 620 LB front springs (installed) 2 Tubular Upper Control Arms (installed) 2 Tubular Lower Control Arms (installed) 2 Spring Perch (installed) 2 Upper Ball Joint Wedge Kit (installed) 2 CPP Mini Sub frame Kit (installed) 1 Steel Brake Line (MC to rear) 1 Steel Gas Line (engine to tank) 1 Front Disc Brake Brakets and Rotors (installed) 2 Outer Tie Rods 2 Trunk Lid (aftermarket) 1 Door Shells (aftermarket) 2 Under Dash AC Unit (core) 1 Pony Door Panel Kit 1 Carpet underlayment 1 Window Felt Kit 1 Autolite 4100 4BBL Carb (rebuilt) 1 New Glove box Door - Wood Grain 1 Sun Visors (pair) 1 Seat Bolt Plug Kit (4 plugs) 2 Front Disc Brake Hoses 2 Trunk Mat 1 Throw-out Bearing 1 Rear Axle Seals 2 Firewall to Headlamp wiring Harness 2 Complete Body Gromet kit 1 Ford Motorsports Breather Cap 1 Parking Brake Handle 1 Vent Window Division Bar Gasket 5 Tail Light Gasket 2 Brake Hose Bolt 1 Right Side outer Door Handle 1 HI-PO Fender Emblem 2 Wire Loom Mounting Clip Kit 1 Seat Stop Kit 1 Power Brake Check Valve and Grommet 1 Wire Loom Kit 2